{"title":"SPOILBOARD SYSTEM","description":null,"products":[{"product_id":"split-expansion-anchor","title":"Split Expansion Anchor","description":"\u003cp\u003eThe \u003cstrong\u003eSplit Expansion Anchor\u003c\/strong\u003e is a removable mounting component designed for the Broinwood CNC Spoilboard System.\u003c\/p\u003e\n\u003cp\u003eIt installs into a machined pocket in an MDF spoilboard and uses a \u003cstrong\u003eThreaded Insert\u003c\/strong\u003e to expand the two halves of the anchor against the pocket walls. Once expanded, it creates a secure \u003cstrong\u003e1\/4\"-20 threaded mounting point\u003c\/strong\u003e for Low-Profile Hold-Down Clamps and other compatible workholding setups.\u003c\/p\u003e\n\u003cp\u003eThe anchor can be removed, repositioned, and reused anywhere within the same spoilboard grid.\u003c\/p\u003e\n\u003ch3\u003eHow to Install\u003c\/h3\u003e\n\u003cp\u003eThe Split Expansion Anchor consists of \u003cstrong\u003etwo different halves\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eOne half has \u003cstrong\u003etwo small holes on the top surface\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eThe matching half has a \u003cstrong\u003eflat top with no holes\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eTogether, these two pieces form one complete Split Expansion Anchor.\u003c\/p\u003e\n\u003col start=\"1\"\u003e\n\u003cli\u003eInsert both halves into a properly sized spoilboard pocket.\u003c\/li\u003e\n\u003cli\u003eInstall the \u003cstrong\u003eThreaded Insert\u003c\/strong\u003e into the center of the anchor.\u003c\/li\u003e\n\u003cli\u003eTighten the Threaded Insert using an Allen wrench.\u003c\/li\u003e\n\u003cli\u003eAs the Threaded Insert is tightened, the two halves expand outward and grip the walls of the MDF pocket.\u003c\/li\u003e\n\u003cli\u003eContinue tightening until there is a gap of about \u003cstrong\u003e1 mm between the two halves on both sides\u003c\/strong\u003e and the head of the Threaded Insert sits \u003cstrong\u003eflush with or slightly below the top surface of the anchor\u003c\/strong\u003e.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003eThese are the easiest visual indicators that the Split Expansion Anchor has been properly installed and expanded.\u003c\/p\u003e\n\u003cp\u003eExcessive torque is not required. If using a drill\/driver, use a \u003cstrong\u003elow clutch setting\u003c\/strong\u003e.\u003c\/p\u003e\n\u003ch3\u003eHow to Remove\u003c\/h3\u003e\n\u003cp\u003eBefore removing the Split Expansion Anchor, \u003cstrong\u003ecompletely unscrew and remove the Threaded Insert\u003c\/strong\u003e. This releases the expansion pressure against the walls of the pocket.\u003c\/p\u003e\n\u003cp\u003eIf the anchor remains firmly seated in the MDF:\u003c\/p\u003e\n\u003col start=\"1\"\u003e\n\u003cli\u003eInsert the removal tool into one of the \u003cstrong\u003etwo small holes on the top of the anchor\u003c\/strong\u003e.\u003c\/li\u003e\n\u003cli\u003eGently move that half away from the pocket wall to release it from the MDF.\u003c\/li\u003e\n\u003cli\u003eInsert the removal tool through the center of the anchor.\u003c\/li\u003e\n\u003cli\u003eEngage the \u003cstrong\u003eextraction slot located at the bottom\u003c\/strong\u003e.\u003c\/li\u003e\n\u003cli\u003ePull upward to remove the anchor from the spoilboard.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003eThe Split Expansion Anchor can then be installed in another pocket and reused.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eHeight:\u003c\/strong\u003e 16 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRecommended nominal pocket diameter:\u003c\/strong\u003e 25.3 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRecommended pocket depth:\u003c\/strong\u003e 17 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThread:\u003c\/strong\u003e 1\/4\"-20\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRecommended bolt relief hole:\u003c\/strong\u003e 8 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstallation:\u003c\/strong\u003e Removable and reusable\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDesigned for:\u003c\/strong\u003e MDF CNC spoilboards\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufactured in:\u003c\/strong\u003e USA\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eImportant\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003e25.3 mm pocket diameter is a recommended nominal size, not an absolute requirement\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eA slightly larger pocket is perfectly acceptable as long as the Guide Pin fits snugly without excessive play. The actual pocket diameter may vary depending on your CNC machine, tooling, calibration, and cutting accuracy.\u003c\/p\u003e\n\u003cp\u003eBefore machining the complete spoilboard, I recommend starting with a \u003cstrong\u003e25.0 mm test pocket\u003c\/strong\u003e and checking the fit with a Broinwood Guide Pin.\u003c\/p\u003e\n\u003cp\u003eIf the pocket is too tight, increase the diameter gradually in \u003cstrong\u003e0.1 mm increments\u003c\/strong\u003e until the correct fit is achieved.\u003c\/p\u003e\n\u003cp\u003eThe Guide Pin should fit snugly, but it should still be possible to insert and remove it by hand without excessive force.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eThe fit is more important than the exact diameter.\u003c\/strong\u003e\u003c\/p\u003e\n\u003ch3\u003eStrength\u003c\/h3\u003e\n\u003cp\u003eThe Split Expansion Anchor has been tested for pull-out loads of \u003cstrong\u003eup to 120 kg (265 lb) under my test conditions\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eThis is a test result, \u003cstrong\u003enot a certified or guaranteed working-load rating\u003c\/strong\u003e. Actual holding strength depends on the MDF, pocket dimensions, machining accuracy, installation, material condition, and other factors.\u003c\/p\u003e\n\u003cp\u003eThe anchor is designed to act as a \u003cstrong\u003ereplaceable sacrificial component if excessive torque is applied\u003c\/strong\u003e. Excessive tightening should still always be avoided.\u003c\/p\u003e","brand":"BroinwooD","offers":[{"title":"Default Title","offer_id":52478613094690,"sku":null,"price":1.2,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0247\/1546\/0683\/files\/512E26C5-456D-442F-B3FA-416F63861883.jpg?v=1788563494"},{"product_id":"40-mm-guide-pin","title":"40 mm Guide Pin","description":"\u003cp\u003eThe \u003cstrong\u003e40 mm Guide Pin\u003c\/strong\u003e is a removable positioning and workholding component designed for the Broinwood CNC Spoilboard System.\u003c\/p\u003e\n\u003cp\u003eIt installs directly into the same machined spoilboard pockets used by the Split Expansion Anchors and can be positioned anywhere within the grid.\u003c\/p\u003e\n\u003cp\u003eThe 40 mm height provides a solid reference surface for positioning workpieces and allows the pin to be used as a stop, fence, or support point in different workholding setups.\u003c\/p\u003e\n\u003cp\u003eThe outside surface of the Guide Pin is intentionally textured. The texture provides additional grip inside the MDF pocket and against the edge of the workpiece.\u003c\/p\u003e\n\u003ch3\u003eHow to Use\u003c\/h3\u003e\n\u003col start=\"1\"\u003e\n\u003cli\u003eInsert the 40 mm Guide Pin into any available pocket in the spoilboard grid.\u003c\/li\u003e\n\u003cli\u003ePosition additional Guide Pins as needed to create stops, fences, or reference points for the workpiece.\u003c\/li\u003e\n\u003cli\u003ePosition the workpiece against the Guide Pins and secure it using the appropriate workholding method.\u003c\/li\u003e\n\u003cli\u003eWhen the setup changes, simply remove the Guide Pin and move it to another pocket.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003eThe Guide Pin should fit \u003cstrong\u003esnugly without excessive play\u003c\/strong\u003e, while still being possible to insert and remove by hand.\u003c\/p\u003e\n\u003ch3\u003eEasy Removal\u003c\/h3\u003e\n\u003cp\u003eEach 40 mm Guide Pin has a \u003cstrong\u003eside through-hole\u003c\/strong\u003e designed to make removal easier.\u003c\/p\u003e\n\u003cp\u003eIf the Guide Pin is seated tightly in the MDF pocket, insert an \u003cstrong\u003eAllen wrench, screwdriver, or another suitable tool\u003c\/strong\u003e through the side hole and use it to pull the Guide Pin upward.\u003c\/p\u003e\n\u003cp\u003eThis eliminates the need to grip the outside of the Guide Pin with pliers or other tools that could damage its textured surface.\u003c\/p\u003e\n\u003ch3\u003eAdditional Workholding Option\u003c\/h3\u003e\n\u003cp\u003eThe 40 mm Guide Pin can also accept a \u003cstrong\u003eThreaded Insert\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eOnce the Threaded Insert is installed, a \u003cstrong\u003e1\/4\"-20 bolt\u003c\/strong\u003e can be threaded into the Guide Pin and used as an adjustable pushing or holding point against the workpiece.\u003c\/p\u003e\n\u003cp\u003eThis allows the same Guide Pin to be used not only for positioning, but also to apply additional side pressure when required by the setup.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eHeight:\u003c\/strong\u003e 40 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOuter surface:\u003c\/strong\u003e Textured\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOuter diameter range:\u003c\/strong\u003e approximately 25.01–25.35 mm across the textured surface\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRecommended starting pocket diameter:\u003c\/strong\u003e 25.3 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRecommended pocket depth:\u003c\/strong\u003e 17 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThreaded Insert compatibility:\u003c\/strong\u003e 1\/4\"-20\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstallation:\u003c\/strong\u003e Removable and reusable\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDesigned for:\u003c\/strong\u003e MDF CNC spoilboards\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufactured in:\u003c\/strong\u003e USA\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eImportant\u003c\/h3\u003e\n\u003cp\u003eBecause of its intentionally textured outer surface, the 40 mm Guide Pin does \u003cstrong\u003enot have one constant outside diameter\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eDepending on where the measurement is taken across the textured profile, the outside diameter can range from approximately \u003cstrong\u003e25.01 mm to 25.35 mm\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eFor this reason, the correct pocket size should be determined by \u003cstrong\u003eactual fit rather than by measuring the outside diameter of the Guide Pin\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eBefore machining the complete spoilboard grid, I recommend starting with a \u003cstrong\u003e25.0 mm test pocket\u003c\/strong\u003e and checking the fit with the Guide Pin.\u003c\/p\u003e\n\u003cp\u003eIf the pocket is too tight, increase the diameter gradually in \u003cstrong\u003e0.1 mm increments\u003c\/strong\u003e and test the fit again. In most setups, the final pocket diameter will be around \u003cstrong\u003e25.3 mm\u003c\/strong\u003e, but a slightly larger pocket is perfectly acceptable if needed.\u003c\/p\u003e\n\u003cp\u003eThe Guide Pin should fit snugly without excessive play, but it should still be possible to insert and remove it by hand without excessive force.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eThe correct fit is more important than the exact pocket diameter.\u003c\/strong\u003e\u003c\/p\u003e","brand":"BroinwooD","offers":[{"title":"Default Title","offer_id":52478616994082,"sku":null,"price":1.2,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0247\/1546\/0683\/files\/BA664320-E5B2-450F-A383-385182DA9BEC.jpg?v=1788562289"},{"product_id":"low-profile-hold-down-clamp","title":"Low-Profile Hold-Down Clamp","description":"\u003cp\u003eThe \u003cstrong\u003eLow-Profile Hold-Down Clamp\u003c\/strong\u003e is designed for securing workpieces to the Broinwood CNC Spoilboard System while keeping the clamping hardware as low as possible above the work surface.\u003c\/p\u003e\n\u003cp\u003eThe clamp mounts to a \u003cstrong\u003eSplit Expansion Anchor\u003c\/strong\u003e using a 1\/4\"-20 bolt. Its elongated center slot allows the clamp to slide forward or backward, making it easy to position the clamping point where it is needed.\u003c\/p\u003e\n\u003cp\u003eThe low-profile design is especially useful for thinner workpieces and CNC operations where keeping the workholding hardware away from the toolpath is important.\u003c\/p\u003e\n\u003ch3\u003eHow to Use\u003c\/h3\u003e\n\u003col start=\"1\"\u003e\n\u003cli\u003eInstall a \u003cstrong\u003eSplit Expansion Anchor\u003c\/strong\u003e in a suitable pocket near the workpiece.\u003c\/li\u003e\n\u003cli\u003ePosition the Low-Profile Hold-Down Clamp over the anchor.\u003c\/li\u003e\n\u003cli\u003eInsert a \u003cstrong\u003e1\/4\"-20 bolt\u003c\/strong\u003e through the center slot and thread it into the Threaded Insert.\u003c\/li\u003e\n\u003cli\u003eSlide the clamp toward the workpiece until the appropriate step engages the edge of the material.\u003c\/li\u003e\n\u003cli\u003eTighten the bolt until the workpiece is held securely.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003eDo not overtighten. Use only the amount of clamping force required to hold the workpiece securely.\u003c\/p\u003e\n\u003ch3\u003eAdjustable Step Heights\u003c\/h3\u003e\n\u003cp\u003eThe clamp has \u003cstrong\u003etwo different stepped profiles\u003c\/strong\u003e, allowing the clamping height to be adjusted for different workpiece thicknesses.\u003c\/p\u003e\n\u003cp\u003eOne end has \u003cstrong\u003esmaller, finer steps\u003c\/strong\u003e, while the opposite end has \u003cstrong\u003elarger steps\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eSimply rotate the clamp and select the side and step that best matches the height of your workpiece.\u003c\/p\u003e\n\u003cp\u003eThis provides multiple clamping-height options without requiring additional spacers or different clamp sizes.\u003c\/p\u003e\n\u003ch3\u003eTactile Orientation Indicator\u003c\/h3\u003e\n\u003cp\u003eA small raised indicator is built into one side of the clamp so you can identify the orientation by touch without having to flip the clamp over and visually check the steps.\u003c\/p\u003e\n\u003cp\u003eWhen the raised indicator is on the \u003cstrong\u003eright side\u003c\/strong\u003e, the \u003cstrong\u003esmaller steps\u003c\/strong\u003e are facing toward you.\u003c\/p\u003e\n\u003cp\u003eWhen the raised indicator is on the \u003cstrong\u003eleft side\u003c\/strong\u003e, the \u003cstrong\u003elarger steps\u003c\/strong\u003e are facing toward you.\u003c\/p\u003e\n\u003cp\u003eThis makes it faster and easier to select the correct step profile during setup.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eOverall length:\u003c\/strong\u003e 80 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWidth:\u003c\/strong\u003e 20 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThickness:\u003c\/strong\u003e 12 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSlot length:\u003c\/strong\u003e 57.5 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSlot width:\u003c\/strong\u003e 7 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting:\u003c\/strong\u003e 1\/4\"-20 bolt\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eClamping height:\u003c\/strong\u003e Multiple stepped positions\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStep profiles:\u003c\/strong\u003e Fine and large\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOrientation indicator:\u003c\/strong\u003e Tactile raised feature\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstallation:\u003c\/strong\u003e Removable and repositionable\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatible with:\u003c\/strong\u003e Broinwood Split Expansion Anchor\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDesigned for:\u003c\/strong\u003e CNC workholding\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufactured in:\u003c\/strong\u003e USA\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eImportant\u003c\/h3\u003e\n\u003cp\u003eAlways select a step that provides solid contact with the workpiece before tightening the clamp.\u003c\/p\u003e\n\u003cp\u003eThe clamp should apply enough downward holding force to secure the workpiece without excessive tightening.\u003c\/p\u003e\n\u003cp\u003eBefore starting the CNC, \u003cstrong\u003ealways verify that the Low-Profile Hold-Down Clamp, mounting bolt, Split Expansion Anchor, and all other workholding components are completely clear of the programmed toolpath.\u003c\/strong\u003e\u003c\/p\u003e","brand":"CUSTOM CUTTING BOARDS BY BROINWOOD","offers":[{"title":"Default Title","offer_id":52478659494178,"sku":null,"price":1.2,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0247\/1546\/0683\/files\/photo_7_2026-09-04_18-29-13.jpg?v=1788562531"},{"product_id":"30-mm-guide-pin","title":"30 mm Guide Pin","description":"\u003cp\u003eThe \u003cstrong\u003e30 mm Guide Pin\u003c\/strong\u003e is a removable positioning component designed for the Broinwood CNC Spoilboard System.\u003c\/p\u003e\n\u003cp\u003eIt installs directly into the spoilboard grid and can be used as a stop, fence, or reference point for positioning workpieces.\u003c\/p\u003e\n\u003cp\u003eIts lower 30 mm height provides a more compact option when the additional height of the 40 mm Guide Pin is not needed.\u003c\/p\u003e\n\u003cp\u003eThe outside surface is intentionally textured to provide additional grip inside the MDF pocket and against the edge of the workpiece.\u003c\/p\u003e\n\u003ch3\u003eHow to Use\u003c\/h3\u003e\n\u003col start=\"1\"\u003e\n\u003cli\u003eInsert the 30 mm Guide Pin into any available pocket in the spoilboard grid.\u003c\/li\u003e\n\u003cli\u003ePosition additional Guide Pins as needed to create stops, fences, or reference points for the workpiece.\u003c\/li\u003e\n\u003cli\u003ePosition the workpiece against the Guide Pins and secure it using the appropriate workholding method.\u003c\/li\u003e\n\u003cli\u003eWhen the setup changes, remove the Guide Pin and reposition it in another pocket.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003eThe Guide Pin should fit \u003cstrong\u003esnugly without excessive play\u003c\/strong\u003e, while still being possible to insert and remove by hand.\u003c\/p\u003e\n\u003ch3\u003eEasy Removal\u003c\/h3\u003e\n\u003cp\u003eThe 30 mm Guide Pin has a \u003cstrong\u003eside through-hole designed only for removal\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eIf the Guide Pin is seated tightly in the MDF pocket, insert an \u003cstrong\u003eAllen wrench, screwdriver, or another suitable tool\u003c\/strong\u003e through the side hole and use it to pull the Guide Pin upward.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eThe side hole is not designed to accept a Threaded Insert.\u003c\/strong\u003e\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eHeight:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOuter surface:\u003c\/strong\u003e Textured\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOuter diameter range:\u003c\/strong\u003e approximately 25.01–25.35 mm across the textured surface\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRecommended starting pocket diameter:\u003c\/strong\u003e 25.3 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRecommended pocket depth:\u003c\/strong\u003e 17 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSide through-hole:\u003c\/strong\u003e Removal only\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstallation:\u003c\/strong\u003e Removable and reusable\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDesigned for:\u003c\/strong\u003e MDF CNC spoilboards\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufactured in:\u003c\/strong\u003e USA\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eImportant\u003c\/h3\u003e\n\u003cp\u003eBecause of its intentionally textured outer surface, the 30 mm Guide Pin does \u003cstrong\u003enot have one constant outside diameter\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eDepending on where the measurement is taken across the textured profile, the outside diameter can range from approximately \u003cstrong\u003e25.01 mm to 25.35 mm\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eFor this reason, determine the correct pocket size by \u003cstrong\u003eactual fit rather than by measuring the outside diameter of the Guide Pin\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eBefore machining the complete spoilboard grid, I recommend starting with a \u003cstrong\u003e25.0 mm test pocket\u003c\/strong\u003e. If the pocket is too tight, increase the diameter gradually in \u003cstrong\u003e0.1 mm increments\u003c\/strong\u003e until the correct fit is achieved.\u003c\/p\u003e\n\u003cp\u003eIn most setups, the final pocket diameter will be around \u003cstrong\u003e25.3 mm\u003c\/strong\u003e, but a slightly larger pocket is acceptable if needed.\u003c\/p\u003e\n\u003cp\u003eThe Guide Pin should fit snugly without excessive play while still being possible to insert and remove by hand.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eThe correct fit is more important than the exact pocket diameter.\u003c\/strong\u003e\u003c\/p\u003e","brand":"BroinwooD","offers":[{"title":"Default Title","offer_id":52480179503394,"sku":null,"price":1.2,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0247\/1546\/0683\/files\/708740C9-44EA-4DE0-8F85-AEEE251E3F1A.jpg?v=1788578123"},{"product_id":"split-expansion-anchor-removal-tool","title":"Split Expansion Anchor Removal Tool","description":"\u003cp\u003eThe \u003cstrong\u003eSplit Expansion Anchor Removal Tool\u003c\/strong\u003e is designed specifically for releasing and removing Split Expansion Anchors from the Broinwood CNC Spoilboard System.\u003c\/p\u003e\n\u003cp\u003eThe angled tip is used to release the anchor from the wall of the MDF pocket and then engage the extraction slot at the bottom of the anchor for removal.\u003c\/p\u003e\n\u003ch3\u003eHow to Use\u003c\/h3\u003e\n\u003cp\u003eBefore removing a Split Expansion Anchor, \u003cstrong\u003ecompletely unscrew and remove the Threaded Insert\u003c\/strong\u003e.\u003c\/p\u003e\n\u003col start=\"1\"\u003e\n\u003cli\u003eInsert the angled tip of the Removal Tool into one of the \u003cstrong\u003etwo small holes on the top of the Split Expansion Anchor\u003c\/strong\u003e.\u003c\/li\u003e\n\u003cli\u003eGently move the tool toward the center of the anchor. This pulls one half slightly away from the MDF pocket wall and releases the textured surface from the MDF.\u003c\/li\u003e\n\u003cli\u003eOnce the anchor half is released, insert the angled tip through the center opening of the anchor.\u003c\/li\u003e\n\u003cli\u003eEngage the \u003cstrong\u003eextraction slot located at the bottom of the Split Expansion Anchor\u003c\/strong\u003e.\u003c\/li\u003e\n\u003cli\u003ePull upward to remove the anchor from the pocket.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003eIf necessary, repeat the release step on the other half before pulling the anchor out.\u003c\/p\u003e\n\u003ch3\u003eImportant\u003c\/h3\u003e\n\u003cp\u003eAlways \u003cstrong\u003ecompletely remove the Threaded Insert before attempting to remove the Split Expansion Anchor\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eThe Removal Tool is intended to release and extract the anchor only after the expansion pressure has been removed.\u003c\/p\u003e\n\u003cp\u003eDo not attempt to pull the anchor out while the Threaded Insert is still installed and tightened.\u003c\/p\u003e","brand":"BroinwooD","offers":[{"title":"Default Title","offer_id":52480215056674,"sku":null,"price":2.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0247\/1546\/0683\/files\/35BDBA2A-5A05-445E-9083-AB45D29861D3.jpg?v=1788578979"},{"product_id":"complete-spoilboard-system-set","title":"Complete Spoilboard System Set","description":"\u003cp\u003eThe complete set includes:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003e25 × Split Expansion Anchors\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e25 × Threaded Inserts\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e10 × 40 mm Guide Pins\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e5 × 30 mm Guide Pins\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e8 × Low-Profile Hold-Down Clamps\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e2 × Allen Wrenches\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e1 × Split Expansion Anchor Removal Tool\u003cbr\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003e\u003cbr\u003e\u003c\/h3\u003e\n\u003ch3\u003eBolts Not Included\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eMounting bolts are not included with the set.\u003c\/strong\u003e This allows you to choose the bolt lengths that best match your workpiece thickness and setup.\u003c\/p\u003e\n\u003cp\u003eI use \u003cstrong\u003e1\/4\"-20 bolts\u003c\/strong\u003e in several lengths:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003e\u003ca href=\"https:\/\/amzn.to\/3TYYDq8\" target=\"_blank\" rel=\"noopener\"\u003e\u003cspan\u003eBolts — Amazon\u003c\/span\u003e\u003c\/a\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003ca href=\"https:\/\/amzn.to\/3RUSs5R\" target=\"_blank\" rel=\"noopener\"\u003e\u003cspan\u003eBolts — Amazon\u003c\/span\u003e\u003c\/a\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003ca href=\"https:\/\/amzn.to\/4ifysoY\" target=\"_blank\" rel=\"noopener\"\u003e\u003cspan\u003eBolts — Amazon\u003c\/span\u003e\u003c\/a\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003ca href=\"https:\/\/amzn.to\/4qjMJD7\" target=\"_blank\" rel=\"noopener\"\u003e\u003cspan\u003eBolts — Amazon\u003c\/span\u003e\u003c\/a\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e","brand":"BroinwooD","offers":[{"title":"Default Title","offer_id":52480409436450,"sku":null,"price":49.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0247\/1546\/0683\/files\/CodexImageSep4_2026_11_41_51PM.png?v=1788579735"}],"url":"https:\/\/broinwood.com\/collections\/spoilboard-system.oembed","provider":"CUSTOM CUTTING BOARDS BY BROINWOOD","version":"1.0","type":"link"}