{"product_id":"30-mm-guide-pin","title":"30 mm Guide Pin","description":"\u003cp\u003eThe \u003cstrong\u003e30 mm Guide Pin\u003c\/strong\u003e is a removable positioning component designed for the Broinwood CNC Spoilboard System.\u003c\/p\u003e\n\u003cp\u003eIt installs directly into the spoilboard grid and can be used as a stop, fence, or reference point for positioning workpieces.\u003c\/p\u003e\n\u003cp\u003eIts lower 30 mm height provides a more compact option when the additional height of the 40 mm Guide Pin is not needed.\u003c\/p\u003e\n\u003cp\u003eThe outside surface is intentionally textured to provide additional grip inside the MDF pocket and against the edge of the workpiece.\u003c\/p\u003e\n\u003ch3\u003eHow to Use\u003c\/h3\u003e\n\u003col start=\"1\"\u003e\n\u003cli\u003eInsert the 30 mm Guide Pin into any available pocket in the spoilboard grid.\u003c\/li\u003e\n\u003cli\u003ePosition additional Guide Pins as needed to create stops, fences, or reference points for the workpiece.\u003c\/li\u003e\n\u003cli\u003ePosition the workpiece against the Guide Pins and secure it using the appropriate workholding method.\u003c\/li\u003e\n\u003cli\u003eWhen the setup changes, remove the Guide Pin and reposition it in another pocket.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003eThe Guide Pin should fit \u003cstrong\u003esnugly without excessive play\u003c\/strong\u003e, while still being possible to insert and remove by hand.\u003c\/p\u003e\n\u003ch3\u003eEasy Removal\u003c\/h3\u003e\n\u003cp\u003eThe 30 mm Guide Pin has a \u003cstrong\u003eside through-hole designed only for removal\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eIf the Guide Pin is seated tightly in the MDF pocket, insert an \u003cstrong\u003eAllen wrench, screwdriver, or another suitable tool\u003c\/strong\u003e through the side hole and use it to pull the Guide Pin upward.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eThe side hole is not designed to accept a Threaded Insert.\u003c\/strong\u003e\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eHeight:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOuter surface:\u003c\/strong\u003e Textured\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOuter diameter range:\u003c\/strong\u003e approximately 25.01–25.35 mm across the textured surface\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRecommended starting pocket diameter:\u003c\/strong\u003e 25.3 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRecommended pocket depth:\u003c\/strong\u003e 17 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSide through-hole:\u003c\/strong\u003e Removal only\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstallation:\u003c\/strong\u003e Removable and reusable\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDesigned for:\u003c\/strong\u003e MDF CNC spoilboards\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufactured in:\u003c\/strong\u003e USA\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eImportant\u003c\/h3\u003e\n\u003cp\u003eBecause of its intentionally textured outer surface, the 30 mm Guide Pin does \u003cstrong\u003enot have one constant outside diameter\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eDepending on where the measurement is taken across the textured profile, the outside diameter can range from approximately \u003cstrong\u003e25.01 mm to 25.35 mm\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eFor this reason, determine the correct pocket size by \u003cstrong\u003eactual fit rather than by measuring the outside diameter of the Guide Pin\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eBefore machining the complete spoilboard grid, I recommend starting with a \u003cstrong\u003e25.0 mm test pocket\u003c\/strong\u003e. If the pocket is too tight, increase the diameter gradually in \u003cstrong\u003e0.1 mm increments\u003c\/strong\u003e until the correct fit is achieved.\u003c\/p\u003e\n\u003cp\u003eIn most setups, the final pocket diameter will be around \u003cstrong\u003e25.3 mm\u003c\/strong\u003e, but a slightly larger pocket is acceptable if needed.\u003c\/p\u003e\n\u003cp\u003eThe Guide Pin should fit snugly without excessive play while still being possible to insert and remove by hand.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eThe correct fit is more important than the exact pocket diameter.\u003c\/strong\u003e\u003c\/p\u003e","brand":"BroinwooD","offers":[{"title":"Default Title","offer_id":52480179503394,"sku":null,"price":1.2,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0247\/1546\/0683\/files\/708740C9-44EA-4DE0-8F85-AEEE251E3F1A.jpg?v=1788578123","url":"https:\/\/broinwood.com\/products\/30-mm-guide-pin","provider":"CUSTOM CUTTING BOARDS BY BROINWOOD","version":"1.0","type":"link"}